|
|
|
#61
07-03-2012, 11:05 AM
|
|||
|
|||
man has it been that long since i updated!! i will take pictures tomorrow and update this thread! my chevelle is going to be back on all 4 tomorrow as long as i have the whole day to myself
__________________
2005 dodge magnum daily driver 1988 mazda rx7 LS6 swap 1969 SS work in progress 
|
|
#62
08-17-2012, 09:35 PM
|
|||
|
|||
|
i waited all morning for my part and it never showed up! so here is what i did today
 new wheel lug finally in and wheels installed until i figure out if i want to keep them or not cleaned the inside of the car because i needed to do it to make me feel better   then at 8pm look what shows up  the part i waited for finally showed up when i am cleaning up and getting ready to eat dinner!..lol
__________________
2005 dodge magnum daily driver 1988 mazda rx7 LS6 swap 1969 SS work in progress
|
|
#63
08-22-2012, 01:29 PM
|
|||
|
|||
|
did not have much time today but i took out my 4 speed manual trans to get it ready for the 6 speed
    not going to have much time this week to do it but i am hoping to have it in by sunday!
__________________
2005 dodge magnum daily driver 1988 mazda rx7 LS6 swap 1969 SS work in progress
|
|
#64
10-07-2012, 07:48 PM
|
|||
|
|||
|
well its been a LONG time since i had time to work on my chevelle. But i finally got the t56 under the car and INSTALLEd very little cutting. about as much as putting in a tko
__________________
2005 dodge magnum daily driver 1988 mazda rx7 LS6 swap 1969 SS work in progress
|
|
#65
11-25-2012, 08:10 PM
|
|||
|
|||
|
got a new (well used but new for me) intake
 installed the starter in wrong  and so happy i found the right bolts to move it over  now that its in correct i can work on putting the t56 in  this is all i had to cut for the t56 now that i got that done i said i was going to work on my brake system so i started from the rear new hard lines and not pictured but the new rubber line too 
__________________
2005 dodge magnum daily driver 1988 mazda rx7 LS6 swap 1969 SS work in progress
|
|
#66
11-25-2012, 08:14 PM
|
|||
|
|||
|
new front brakes and bearings
 new rubber lines and metal lines  new metal lines waiting for the hold off valve  new booster and master (and yes its painted) 
__________________
2005 dodge magnum daily driver 1988 mazda rx7 LS6 swap 1969 SS work in progress
|
|
#67
11-25-2012, 08:17 PM
|
|||
|
|||
|
new dis block on the frame with all new lines as well
 passenger side metal and rubber lines  ran in the stock locations  new metal line from the dis block to the rear  and t56 on the trans brace now just waiting for the drive shaft 
__________________
2005 dodge magnum daily driver 1988 mazda rx7 LS6 swap 1969 SS work in progress
|
|
#68
11-25-2012, 10:15 PM
|
||||
|
||||
|
It could be the picture but your distribution block is looking way to close to your headers. I have read where it needs to be moved when using headers. Otherwise looking good.
__________________
Ray 1970 SS Chevelle Van Nuys Built
|
|
#69
11-25-2012, 10:52 PM
|
|||
|
|||
|
yeah i have to bend it back because when i was trying to get the one on the bottom loose i bent the arm that holds it in place.
__________________
2005 dodge magnum daily driver 1988 mazda rx7 LS6 swap 1969 SS work in progress
|
|
#70
12-10-2012, 08:36 AM
|
|||
|
|||
|
got the wheels for the chevelle. I need to get the correct lugs for it but here they are
17x8 all around with 255/45/17s on it for now 
__________________
2005 dodge magnum daily driver 1988 mazda rx7 LS6 swap 1969 SS work in progress
|
 |
|
|
Linear Mode
