|
|
|
#361
03-15-2012, 05:31 PM
|
|||
|
|||
I finished installing the harmonic balancer, and finally painted the entire engine orange. Waiting on a tool I ordered to arrive so I can get my pushrod length measured and order what I need.
__________________
1972 SS 454 Chevelle LS5/M21/12 bolt 3.73 posi 1969 Malibu COPO L72/M20/12 bolt 3.31 posi 1968 Malibu LQ9/4L80E/12 bolt 3.73 posi 
|
|
#362
03-15-2012, 08:04 PM
|
|||
|
|||
|
Again I did nothing to the Chevelle ,Im doing yard and tree work. Im removing 3 trees in preparation for a pole barn for the newly restored(soon I hope) truck to park under .
__________________
John
|
|
#363
03-15-2012, 09:38 PM
|
||||
|
||||
|
grumpy and I discussed going to Summit while we are in Cleveland for the show on Friday. We need to pick up the air conditioning and the mufflers. Depends on if we want to add another 1 1/2 hours to our already 3 -3 1/2 hour trip.
__________________
Get in, sit down, shut up, hold on...cause Ms Grumpy is driving ! For the audio geek try: www.audiokarma.org
|
|
#364
03-15-2012, 10:38 PM
|
|||
|
|||
|
You can get the A/C cheaper than Summit from a place in Florida ,no sales tax and free shipping .Summit would not meet their price because they could not look it up on the net. I saved about $150 on the one for my truck which was considerably higher than those for the Chevelle if you are using Vintage Air.
__________________
John
|
|
#366
03-16-2012, 07:40 PM
|
||||
|
||||
|
Put in the new oil pressure gauge, installed kick panels with speakers & picked up my new driveshaft. Putting new carpet in tomorrow along with the driveshaft and 1350 yokes. There is a chance I could actually drive this thing by the end of the day....
__________________
Eric 496 cu. in. "cruiser" Assembled & tuned by Mo's Speed Shop - Dallas, GA
|
|
#367
03-16-2012, 07:50 PM
|
||||
|
||||
|
Quote:
Good thing that we didn't stop at Summit, just no time.
__________________
Get in, sit down, shut up, hold on...cause Ms Grumpy is driving ! For the audio geek try: www.audiokarma.org
|
|
#369
03-18-2012, 04:44 PM
|
|||
|
|||
|
Started to sand down the engine cross member and frame rails. Looks like I'll be removing the center link and steering box soon. I am trying to get the engine bay detailed the rest of the way ASAP. I should be ordering a set of pushrods by the weeks end. I am beyond ready to get the engine and transmission installed in the car. It will get a lot of crap off the floor and out of the house.
__________________
1972 SS 454 Chevelle LS5/M21/12 bolt 3.73 posi 1969 Malibu COPO L72/M20/12 bolt 3.31 posi 1968 Malibu LQ9/4L80E/12 bolt 3.73 posi
|
|
#370
03-18-2012, 05:07 PM
|
||||
|
||||
|
I went to check on the progress of mine yesterday.
__________________
Jay 69 Chevelle SS396(454), (M21), (3.73) Cortez Silver 2009 Audi S8 V10 5.2 Supercar, 2009 Cadilac Escalade V8 6.2
|
 |
|
|
Linear Mode
